Build your hive is like a treat, especially if you like to do such things in terms of craftsmanship. If you are not sure about is yourself, you can let an experienced carpentry to do it for you. The important thing here is that you are good, how it informs the proper way to get the right design hive construction.
There are two ways that you are going to do it, assuming you do it yourself. First, you can purchase a depressed beehive and assemble them as instructed, or second to start from scratch to make your own equipment and parts of the hive.
Whatever your choice, please remember that you are on the design, dimension and mounting method to a standard that is more the Langstroth hive design. This gives you flexibility in the future to replace parts and even other made parts where incompatibility will not be a problem.
The movable frame Langstroth hive has been carefully designed to include all the practical factors such as design simplicity, easy to use, allowing quick hive inspection and interchangeability of frames. There are Langstroth designs that you can buy to be used as reference.
Below is an example of how you drag parts of the hive, the mount frame and extras. General Tips · The use of flat cedar or pine wood for all parts of the hive is proposed construction.
· You can make a node when it is needed, but it should not be at the edge of the woods, or if you are planning to make a handle.
· Consider the dryness of the wood. If it is not completely dry, you should provide some allowance for shrinkage.
· Exception of materials that are used, for the hive top cover and bottom plate floor, where it should be made of plywood, through the damp and temperature fluctuations is less affected.
· Pieces of wood must be cut with precision to standard dimensions. The depth of a handle should be exactly 16 mm 5/8 inches.
· Bee areas should be exactly 8 mm or 5/16 inch. A bee space is the exact distance between combs in the hive.
Installation of extras Super, the structure holding the frame. It has a standard external length of 50.7 cm (20 inches) and a width of 41.8 cm (16.5 inches), the depth may vary in three dimensions common: · Standard: 24 cm (9.5 inches) for breeding and extras · Dadant: 16.8 cm (6 5/8 inches) for breeding and extras · Low: 14.7 cm (5 13/16 inches), only for extras
Recommended nails nail extras, the base plate and the cover are 50 mm (1 1/8 inch) long nails. If available, you can use an electric stapler for your ease. Screws are good substitutes for the nails, if you want maximum durability.
Assembly procedures vary, but here is a good recommendation that you could follow: 1 (Please no thumbtacks) rested metal nail to finish in pieces, using 16 mm (5/8 inch) common nails 2 Build using brackets 3 Nail through the top of the page Share 4 Take the clamp to the super-rotate, stretch and nail the other end 5 Take the terminal, check diagonals to ensure that the place is super- 6 Finish it by nailing through the sides of the end pieces
The holding power of nails driven increase when you drive the nails at an angle to the grain. To gain additional strength, the end pieces can be glued before nailing. You may have to fix some metal parts, which are the frame rests and hive-top covers that are made of galvanized iron, aluminum or other suitable metal may
Installation and wiring frames It is best if you will buy the frame and frame parts in your beekeeping supplier that will be able to provide you with the correct dimension. Some areas of your hive, like the frame and the foundation with the plastic ones that are replaced more durable than wood. A sheet of plastic foundation can not be applied also needed on a wooden frame, where wiring for wax foundation are.
When mounting the frame you remember only the specific frame using nails, just to make sure that the frames are square and properly hung in the extras with the right bee hive spaces between the structures. To generate additional strength and durability of the frame, the end pieces can be bonded prior nails.
Frame wiring tips are as follows: 1 Use # 28 gauge steel wire 2 Use at least two horizontal wires for standard frames. Make sure that the wires in the lower holes are, and the third holes from bottom to top 3 With eyes so that nothing in the forest 4 Horizontal wires must cling and secured with 16 mm (5/8 inch) cigar box nails 5 For additional strength, a foundation can be used with vertical wires...
Thank you for coming in Exotic of Pets and read the article about: Bee Hive Construction - Assembling Supers and Frames , help us to Shared this article. hopefully useful to us all.
